Студопедия
Случайная страница | ТОМ-1 | ТОМ-2 | ТОМ-3
АрхитектураБиологияГеографияДругоеИностранные языки
ИнформатикаИсторияКультураЛитератураМатематика
МедицинаМеханикаОбразованиеОхрана трудаПедагогика
ПолитикаПравоПрограммированиеПсихологияРелигия
СоциологияСпортСтроительствоФизикаФилософия
ФинансыХимияЭкологияЭкономикаЭлектроника

Be sure to clean drain plug (2) and install with new washer.

ENGINE MAINTENANCE (HR16DE) | CHECKING COOLING SYSTEM FOR LEAKS | Do not allow the coolant container to get too low when filling, to avoid air from being drawn into the cooling system. | INSPECTION AFTER REMOVAL | OIL PRESSURE CHECK | Be sure to clean drain plug and install with new washer. | INSPECTION AFTER INSTALLATION | ENGINE MAINTENANCE (MR18DE) | When draining all of engine coolant in the system, open I | REPLACEMENT PROCEDURES |


Читайте также:
  1. AIR CLEANER FILTER
  2. Be buy clean hurry lose stick take tell wait
  3. Be sure to clean drain plug and install with new washer.
  4. Chapter 1 – The Draining Lake
  5. Clean and Open American Elections
  6. Clean delicious free fresh full good new special sure wonderful

6. Refill with new engine oil. Refer to MA-14. CAUTION:

• The refill capacity depends on the engine oil temperature and drain time. Use these specifications for reference only.

Always use oil level gauge to determine the proper amount of engine oil in the engine.

7. Warm up engine and check area around drain plug (2) and oil fil- ter (3) for engine oil leakage.

8. Stop engine and wait for 10 minutes.

9. Check the engine oil level. Refer to MA-30, "ENGINE OIL: Inspection".

 

OIL FILTER

OIL FILTER: Removal and Installation

 

REMOVAL

1. Remove oil filter using Tool (A).

: Front

Tool number: KV10115801 (J-38956) WARNING:

Be careful not to get burned when engine and engine oil may be hot.

CAUTION:

Oil filter is provided with relief valve. Use Genuine NISSAN Oil Filter or equivalent.

When removing, prepare a shop cloth to absorb any engine oil leakage or spillage.

Do not spill engine oil on drive belt.

Completely wipe off any engine oil that spills on engine and vehicle.

INSTALLATION

1. Remove foreign materials adhering to the oil filter installation surface.

2. Apply new engine oil to the oil seal contact surface of new oil fil- ter.


 

A

 

B

 

C

 

D

 

E

 

F

 

G

PBIC3915E

 

 

H

INFOID:0000000004683696

 

 

I

 

J

 

K

 

MA

PBIC3818E

 

M

 

N

 

O

 

P


 

SMA010

 


Revision: October 2008


MA-33


2009 Versa


3. Screw oil filter manually until it touches the installation surface, then tighten it by 2/3 turn. Or tighten to specification.

 

Oil filter:: 17.7 N·m (1.8 kg-m, 13 ft-lb)

 

SMA229B

 

INSPECTION AFTER INSTALLATION

1. Check the engine oil level. Refer to MA-30, "ENGINE OIL: Inspection".

2. Start engine, and make sure there are no leaks of engine oil.

3. Stop engine and wait for 10 minutes.

4. Check the engine oil level and adjust as necessary. Refer to MA-30, "ENGINE OIL: Inspection".

SPARK PLUG

SPARK PLUG: Component INFOID:0000000004683697

 

  PBIC3536J
  1.   PCV hose   2.   Rocker cover   3.   Spark plug  
4. Ignition coil 5. PCV hose 6. PCV valve  
7. A. O-ring To air duct 8. B. Gasket Refer to MA-35.     C.     To intake manifold  

 


Revision: October 2008


MA-34


2009 Versa


SPARK PLUG: Removal and Installation INFOID:0000000004683698

A

REMOVAL

1. Remove spark plug using suitable tool.

CAUTION: B


Дата добавления: 2015-11-16; просмотров: 49 | Нарушение авторских прав


<== предыдущая страница | следующая страница ==>
AIR CLEANER FILTER| Never drop or shock it.

mybiblioteka.su - 2015-2024 год. (0.006 сек.)