Студопедия
Случайная страница | ТОМ-1 | ТОМ-2 | ТОМ-3
АрхитектураБиологияГеографияДругоеИностранные языки
ИнформатикаИсторияКультураЛитератураМатематика
МедицинаМеханикаОбразованиеОхрана трудаПедагогика
ПолитикаПравоПрограммированиеПсихологияРелигия
СоциологияСпортСтроительствоФизикаФилософия
ФинансыХимияЭкологияЭкономикаЭлектроника

Do not allow the coolant container to get too low when filling, to avoid air from being drawn into the cooling system.

Injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the SRS section. | Battery, and wait at least 3 minutes before performing any service. | GENERAL MAINTENANCE | PERIODIC MAINTENANCE | Chassis and Body Maintenance | Emission Control System Maintenance | RECOMMENDED FLUIDS AND LUBRICANTS | ENGINE MAINTENANCE (HR16DE) | OIL PRESSURE CHECK | Be sure to clean drain plug and install with new washer. |


Читайте также:
  1. A well-regulated militia being necessary to the freedom of a free state, the right of the people to keep and bear arms shall not be abridged.
  2. A. I am a team leader. I am proud of it. – I am proud of being a team leader.
  3. Allow, permit, advise, forbid
  4. Any human being taking initiation with the name and mantra of the Supreme
  5. At that time many mistakes were done. Only one worked trouble-free: our people resignedly allowed to stop up with themselves all holes successfully framed by “effectual measures”.
  6. Avoid catastrophe
  7. Avoidance of unnecessary stuff

11. Remove the Tool from the radiator neck opening. G

12. Fill the cooling system reservoir tank to the specified level and install the radiator cap. Run the engine to warm up the cooling system and top up the system as necessary.

FLUSHING COOLING SYSTEM H

1. Install reservoir tank if removed. Refer to CO-16, "Component".

2. Install radiator drain plug. I

• If water drain plug on cylinder block is removed, close and tighten it. Refer to EM-96, "Disassem-

bly and Assembly". CAUTION:

Be sure to clean radiator drain plug and install with new O-ring. Refer to CO-16, "Component". J

3. Fill radiator and reservoir tank with water and reinstall radiator cap.

4. Run engine and warm it up to normal operating temperature.

5. Rev engine two or three times under no-load. K

6. Stop engine and wait until it cools down.

7. Drain water from the cooling system. MA

8. Repeat steps 1 through 7 until clear water begins to drain from radiator.

FUEL LINES

M

FUEL LINES: Checking Fuel Line INFOID:0000000004803414

Inspect fuel lines, fuel filler cap and fuel tank for improper attach-

ment, leaks, cracks, damage, loose connections, chafing or deterio- N

ration.

If necessary, repair or replace damaged parts.

O

 

P

 

 


AIR CLEANER FILTER


SMA803A


 

 


Revision: October 2008


MA-19


2009 Versa


AIR CLEANER FILTER: Removal and Installation INFOID:0000000004806007

 

REMOVAL

1. Push the tabs (A) of both ends of the air cleaner cover (1) into the inside (B).

2. Pull up the air cleaner cover (1) and remove it (C).

 

 

PBIC3557J

 

3. Remove air cleaner filter (1) and holder (2) assembly from the air cleaner case.

4. Remove the air cleaner filter (1) from the holder (2).

 

 


 


Дата добавления: 2015-11-16; просмотров: 105 | Нарушение авторских прав


<== предыдущая страница | следующая страница ==>
CHECKING COOLING SYSTEM FOR LEAKS| INSPECTION AFTER REMOVAL

mybiblioteka.su - 2015-2024 год. (0.006 сек.)