Студопедия
Случайная страница | ТОМ-1 | ТОМ-2 | ТОМ-3
АвтомобилиАстрономияБиологияГеографияДом и садДругие языкиДругоеИнформатика
ИсторияКультураЛитератураЛогикаМатематикаМедицинаМеталлургияМеханика
ОбразованиеОхрана трудаПедагогикаПолитикаПравоПсихологияРелигияРиторика
СоциологияСпортСтроительствоТехнологияТуризмФизикаФилософияФинансы
ХимияЧерчениеЭкологияЭкономикаЭлектроника

Task: PUMP 6014_Pumps, Seals and bearings

Читайте также:
  1. Front wheel bearings
  2. Grasp the swingarm at the ends to check for play in its pivot bearings
  3. Selection of rolling bearings

Score: 70.00 %

Passed: Yes

Time Limit: None

Time Spent: 00:00:00

Total Questions: 10

Correct: 7

Incorrect: 3
_______________________________________________


Question 1:


The sealing ring of a stationary mechanical seal:


A - Is held stationary
B - Serves to distribute sealing liquid
C - Does not require an O-ring
D - Rotates with the shaft

Correctness Rule: Single Correct Answer Required

Answer(s) Given: D
Correct Answer(s): A
Marked as: Incorrect

_______________________________________________


Question 2:


Packing in the stuffing box of a pump:


A - Should stop leakage entirely
B - Requires no lubrication
C - Should not stop leakage entirely
D - Will not wear the pump shaft

Correctness Rule: Single Correct Answer Required

Answer(s) Given: C
Correct Answer(s): C
Marked as: Correct

_______________________________________________


Question 3:


In a rotating mechanical seal:


A - A shell secured to the shaft by setscrews holds the sealing ring so that it turns with the shaft
B - A shell secured to the shaft by setscrews holds the mating ring so that it turns with the shaft
C - There is no need for O-rings because the mating surfaces provide the seal
D - A raised shoulder on the shaft accommodates the mating ring

Correctness Rule: Single Correct Answer Required

Answer(s) Given: A
Correct Answer(s): A
Marked as: Correct

_______________________________________________


Question 4:


The type of bearing used in pumps in the illustration is called a:

 

 


A - Cylinder roller bearing
B - Needle roller bearing
C - Spherical roller bearing
D - Deep groove ball bearing

Correctness Rule: Single Correct Answer Required

Answer(s) Given: B
Correct Answer(s): B
Marked as: Correct

_______________________________________________


Question 5:


The mechanical seal configuration where the sliding faces of two spring backed seals run against a common stationary seat is called:


A - Face to face
B - Tandem
C - Concentric
D - Back to back

Correctness Rule: Single Correct Answer Required

Answer(s) Given: A
Correct Answer(s): A
Marked as: Correct

_______________________________________________


Question 6:


The component of a rotating mechanical seal that is held stationary in a recessed part of the pump housing, or the seal housing cover, is referred to as:


A - The mating ring
B - The O-ring
C - The sealing ring
D - The shell

Correctness Rule: Single Correct Answer Required

Answer(s) Given: C
Correct Answer(s): A
Marked as: Incorrect

_______________________________________________


Question 7:


The mating ring of a mechanical seal:


A - Holds the stuffing box packing in place
B - Is held in position by a spring
C - Is positioned so that it has no contact with the sealing ring
D - Is positioned with its face in contact with that of the sealing ring

Correctness Rule: Single Correct Answer Required

Answer(s) Given: D
Correct Answer(s): D
Marked as: Correct

_______________________________________________


Question 8:


A mechanical seal, known as a "pusher" type:


A - Uses a bellows to provide the necessary spring loading for seal face contact
B - Does not use a dynamic secondary seal or o-ring
C - Has a single spring coil fits over the shaft and bellows
D - Uses a dynamic secondary seal or o-ring that seals the fluid path

Correctness Rule: Single Correct Answer Required

Answer(s) Given: D
Correct Answer(s): D
Marked as: Correct

_______________________________________________


Question 9:


What should a pump that operates with negative suction pressure be equipped with to prevent air being drawn into the casing?


A - stuffing boxes and auto-lubricators
B - packing rings and a pump shaft
C - lantern rings and sealing water connections
D - shaft sleeves and sleeve adjustment nuts

Correctness Rule: Single Correct Answer Required

Answer(s) Given: C
Correct Answer(s): C
Marked as: Correct

_______________________________________________


Question 10:


The gland that holds the packing inside the stuffing box must not be tightened too much, because:


A - The shaft must be allowed to create friction against the packing for pressure
B - A negative suction pressure is needed along the shaft to lubricate and cool the packing
C - A small amount of leakage is needed along the shaft to lubricate and cool the packing
D - The shaft sleeve will not be able to rotate, causing excess friction

Correctness Rule: Single Correct Answer Required

Answer(s) Given: B
Correct Answer(s): C
Marked as: Incorrect


 


 


Дата добавления: 2015-10-30; просмотров: 151 | Нарушение авторских прав


Читайте в этой же книге: Капельная ирригационная система | Каннабис и гидропоника | Уход за растениями | Искривление светом | Увеличение урожая | Зараженного помещения | Введение в основы генетики | Как получить чистый сорт | Чтобы сохранить родительские растения используйте вегетаивное размножение! Один и тот же генетический материал будет передаваться от клона к клону. | Поправка: 0.02 грамма кислоты Gibrellic, а НЕ 2 грамма |
<== предыдущая страница | следующая страница ==>
Name: Rustam, Begyssov| Using the Period

mybiblioteka.su - 2015-2024 год. (0.006 сек.)