Detach the pieces from the photo-etched brass plate.

FIG. 1O7

Remove any imperfection or excess material.

FIG. 108

Paint the entire surface of nameplate 170/B.

FIG. 109

Let the paint dry completely, then sand the surfaces in relief with extra fine sandpaper.

FIG. 110

The result is a colored background with brass-colored parts in relief.

FIG. 111

Position the nameplate, following the curve of the transom and over the taff-rail. To position the ends of the nameplate on pieces 169/C (left and right), bend them slightly and gently. Position the taff rail 170/A, shortening it somewhat.

FIG. 112

Position windows 170/C.

FIG. 113

Position momentarily a quarter gallery (171) on one side of the ship towards stern. Trace the shape of the piece on the wales.

FIG. 114

Remove a layer strip in the traced zone where the quarter gallery will be applied.

FIG. 115-116

Clue the quarter gallery In Its frame and repeat the above operations for the opposite gallery.

FIG. 117 HEAD-RAILS

Check pieces 174,175 and 176 with the joints on rails 173 and oh the cutwater. Correct any defects. Clue them on the cutwater perpendicular to the waterline and parallel to each other in the order given in Fig. 120, 121 and 122. Prepare the upper knees 177/A and B and join them with pieces 178/A and B (see Fig. 127, 128, 129) in the dimensions given in Fig. 120. Give the pieces the proper curvature. Clue them as shown in the technical designs.

Prepare lower knees 177/C and D as in Fig. 119. curving and gluing them as illustrated. Prepare central rails 173/B (left and right) and curve them correctly. Study figures 123 to 126 which illustrates the steps towards a correct assembly of these pieces. Be careful that the curvatures of the left and right rails are symmetrical. When the correct shape has been obtained, glue the pieces into place. Prepare now the upper rails 173 (left and right) in the correct curve. File the part of the curve where the catheads will rest. Position and glue the pieces.

FIG. 13O

Make catheads 180 and 181 as Illustrated. Position them on the deck, observing Fig. 120 and Design 2.

FIG. 131

Construct a hook 184 on blocks 183. Rig the tackle as shown and the rope end 182 to bitt 188 (Fig.132).

FIG. 132

Make bitt 188 and position it to the side of the cathead towerds stern. Eliminate a piece of strip 43 in order to fasten the bitt to the bulwark.

FIG. 133

Mount anchors 185. Knot a segment of cable 152 to the ring and put the other end of the cable through the hawse-holes (Fig. 134).

FIG. 135

A buoy for each anchor can be made as shown. The core can be of wood covered with very thin thread. Sling it externally and let run cable 186 for 15-20 mm. In order to fasten it to the anchor crown (Fig. 133). Faten the buoys to the fore shrouds, roll up rope 186 and tie it to the shrouds near the buoy.

FIG. 136

The anchors can be allowed to hang from the cathead, or positioned on their side as in figure 136, tied to a warping bollard.

FIG. 137

Construct the culverin columns 189. NOTE: The four pieces at the fore end should be lower thant those at the stern. See Design 2. Wrap copper band 190 around the top. Make a hole on the top where the culverins 191 will be pinned. Attach columns 189 eliminating a part of the capping and wales when necessary.

FIG. 138

Construct the tackles separately. Fasten them to the cannons and to the bulwark as illustrated in the right hand side of the figure. Position sling 196. Since the cannons are small. It will not be necessary to attach blocks to the cannon tackles.

FIG. 139

MIZZEN MAST 1 left/right - Lower mast shrouds

2 left/right - Topmast shrouds

3 left/right - Backstays

MAIN MAST 4 left/right - Lower shrouds

5 left/right - Topmast shrouds

6 left/right - Topmast backstays

7 left/right - Topgallant backstays
FORE MAST 8 left/right - Lower shrouds

9 left/right - Fore topmast shrouds

10 left/right - Fore topmast backstays

11 left/right - Topgallant backstays

FIG. 140

STAYS 12 Mizzen stay

13 Mizzen topmast stay

14 Main stay

15 Main preventer stay

16 Topmast stay

17 Topmast preventer stay

18 Topgallant stay

19 Fore stay

20 Preventer forestay
21 Fore topmast stay

22 Fore topmast preventer stay

23 Caff stay

24 Bowsprit rack

FIG. 141

Дата добавления: 2015-11-16