Deck accessories

FIG. 54

Prepare the pieces for the cabin. Make the hole for the window on wall 96 only.

FIG. 55

Prepare (from leftover pieces) a few small blocks (strips) to reinforce the inside of the cabin. Construct the cabin in the location given in this figure.

FIG. 56

Plank the walls with strips 102. Plank also the roofs 99 and 100 with strips 102. Position window 103.

FIG. 57

Position coamings 101 and handle 104

FIG. 58

POSITIONING THE CABIN

FIG. 59

Clue rudder wheel 108 on the longest pin of drum 107. Pin the drum to stands 1C5 and 106. Position the whole on the deck. Make sure the axis of drum 107 Is parallel to the waterline by resting the fore end rudder stand on a few thicknesses of wood. Make the tiller 109 (3x3 walnut). On either side of the top of the tiller, position eyebolts with shank 110; shorten the shanks to the correct length. Clean blocks 112. Glue the tiller to the rudder 54. Prepare 4 groups of the following pieces: eyebolt 110, ring 111, and block 112. Make the holes in the deck where each group will be glued. Following the overhead view of the deck, start with block 112/A and proceed In the sequence given In Fig.59. Lastly, put thread 113 Into place. FlG. 62

Mount the capstan and make bars C. Flatten a part of the circumference of the base where It will rest on the grating shown In figure 72. The capstan will be glued Into place only after this grating has been made and positioned.

FIG. 63

Assemble and glue the bilge pump 115.

FIG. 64-65

Make grating 118 In the dimensions given in Fig. 64. Make coamings 116 slightly tapered at the base in order to correspond to the athwartship curve of the deck (Fig. 65). Make coamings 117 and glue them to the larger sides of the grating. Clue coamings 116 prepared above. Apply the grating to the deck.

FIG. 66-67

Construct this grating In the same manner as the one above.

FIG. 68

Make holes on strips 122 with a diameter inferior to that of the cannon balls. Clue balls 123 Into place.

FIG. 69

Build coamings 124 and 125 with the same system used above (Fig.69) and position them on the deck as illustrated In Fig.70 and 72.

Construct the internal border with strips 126 (except on the side for the ladder) where grating 127 will rest; the grating should remain flush with coaming 125 (Fig.71). Build the access ladder 128 and position It exactly as shown.

Before positioning mast heels, see Design 3.

All technical designs in Full Scale

FIG. 73-74

Build coamings 129/A and 130/A with the same concave base as before. Coamings 129/B and 130/B remain straight. Make the holes shown In Fig.74. At the fore end of coaming 129/A. make the openings where the anchor cable will pass.

FIG. 75-76

Position strips 131 on the inside for the hatch cover stops. Construct hatch covers 132 In order to cover the entire internal width. Make the holes where the cable will pass. Position strip 135 lengthwise to create a divider effect. Make the holes on the hatch covers where rings 133 and 134 will be attached.

FIG. 77

Make the base for the life-boat with strips 135 and 136. Supports A and B are obtained by using the life-boat hull as a template. The life-boat must be tied to the base, and can be covered as shown In Design 1. Figure 1.

P.S.) For the mast heels, see Design 3.

FIG. 80

Дата добавления: 2015-11-16