Читайте также: |
|
DESIGN 2
FIG.1 Attaching the riggings to the deck
All technical designs are in full scale
P = Beginning rigging N.
> = Passage rigging N.
... = End rigging N.
(Tie the rigging to a pin-rail or cleat
MIZZEN MAST PIN RACK
(attach right and left riggings)
NOTE: The channels are not Illustrated for
Greater graphic clarity.
FIG.2 MAIN MAST PIN RACK FIG.3 FORE MAST PIN RACK FIG.4 BULWARK (internal view)
MASTING
Follow drawings and instructions on Design 3.
Construct the masts using the correct length for each, and taper them In the given manner. The upper parts of the main, lower, and top masts finish with a square section at the masthead. Apply the accessories (ex. lashings, blocks, etc.) before assembling the various parts of the masts and yards. Make sure the masts and yards are inclined correctly with respect to the deck and that the tops and the caps are parallel to the waterline. Position the masts and yards on the deck following the sequence given for mounting of the shrouds (see instructions for the rigging); glue the caps only after fixing the shrouds. Follow the sequence given in the figures to continue assembling the pieces. Read well all notes and designs. To position bases 198, 199, 200, modify accurately the holes in the deck by inserting the masts and determining the exact position of the bases.
FIC.1 MASTS AND YARDS
Mizzen Mast
Fore Mast
Main Mast
FIG.2 LIST OF SAILS
MAIN MAST 276 Main Sail
277 Top Sail
278 Fore topgallant Sail
FORE MAST 279 Main Sail
280 Fore topsail
281 Fore topgallant Sail
MIZZEN MAST 282 Mizzen topsail
283 Caff-Sail
JIBS 284 Jib
285 Flying jib
286 Fore staysail
BOWSPRIT 287 Spritsail
Set of flags
FIG.3 Positioning the cheeks
FIG.4 Construction of the pillows
FIG.5 Positioning the crosstrees bars
FIG.6 Masthead rigging
FIG.7 Positioning the holes and cleats
FIG.8 Positioning the cleats
FIG.9 Rail column joints
FIG. 10 Construction of the top arch
FIG. 11 Mizzen top FIG.12 Fore top FIG. 13 Main top
FIG.14 MAIN MAST
Through hole
Masthead
Make the holes in the caps
And insert the shortened eyebolts
Guardrail
FIG. 15 FORE MAST
Guardrail
FIG. 16 MIZZEN MAST
Through hole
Guardrail
FIG.17 MIZZEN YARDS
Mizzen topsail
Mizzen
Gaff
FIG. 18 Construction and mounting of bumpkins
FIG. 19 PARRELS (Yards)
251 Parrels for yards 237 and 243
252 Parrels for yards 238 and 244
FIG.20 FORE YARDS
Topgallant - Halyard hook
Foretop
Fore main
FIG.21 MAIN YARDS
Topgallant - Halyard hook
Top
Main (Note:Positioned for example)
FIG.22 BOWSPRIT
Bowsprit
Jib boom
Spritsail
To complete the riggings you can add the crowfeet and some winding line to the stays, as well as some reverse riggings as shown.
REVERSE RIGGINGS CROWFEET (1 x top) DEADEYE (mm.2x2) WINDING LINE SEPARATOR (mm.2x2)
DESIGN 4
Stern post and rudder
1 mm. thick
HULL STRUCTURE
All technical designs are In full scale KEEL AND CUTWATER
Sand lateral blocks 23 to 32 following
The order outlined by the line of the frames.
MAKE FROM 2x18x45 mm. wooden strips
Mm. Thick
Mm. Thick
Shape pieces using strips (4x4 mm) as shown. Remove excess material with a file and sand with fine sandpaper.
CUTWATER RUDDER STERN POST
Дата добавления: 2015-11-26; просмотров: 87 | Нарушение авторских прав