Студопедия
Случайная страница | ТОМ-1 | ТОМ-2 | ТОМ-3
АвтомобилиАстрономияБиологияГеографияДом и садДругие языкиДругоеИнформатика
ИсторияКультураЛитератураЛогикаМатематикаМедицинаМеталлургияМеханика
ОбразованиеОхрана трудаПедагогикаПолитикаПравоПсихологияРелигияРиторика
СоциологияСпортСтроительствоТехнологияТуризмФизикаФилософияФинансы
ХимияЧерчениеЭкологияЭкономикаЭлектроника

D . and remove the cowling

Читайте также:
  1. A Remove the lower mounting bolt(s)...
  2. A Unscrew the bolt (arrowed)... 20.7b ... then remove the cam
  3. B ... and remove the battery
  4. B ... then remove the retainer ...
  5. C ... and remove the lockwasher
  6. Fit the clutch pushrod if removed

3.3a Remove the screw (A), the two bolts (B), the two clips (C)...


 



i

the front of the cowling out sway from the frame to free the two lugs on each side from their rubber grommets (see illustration). Carefully draw the cowling rearwards and off the bike, taking care not to bend the front sides excessively (see illustration).

3 On L. N and R models, remove the screw
and the two bolts securing each side of the
seat cowling, the two clips joining the halves
in the middle, and the two screws securing
the underside at the back (see illustrations).
Carefully draw the cowling rearwards and off
the bike, taking care not to bend the front
sides excessively (see illustration).

Installation

4 Installation is the reverse of removal. On L,
N and R models, make sure tie arm on the
lock barrel fits against the release mechanism
lever.


B... and the two screws (arrowed)...

4 Rear view mirrors -

removal and installation


C... and remove the cowling

5 Fairing panels -

removal and installation



 


       
   

hint

Note that a small amount of lubricant (liquid soap or similar) applied to the mounting rubber grommets of the seat cowling will assist the lugs to engage without the need for undue pressure.


Removal

1 Unscrew the two nuts securing each mirror
and remove the mirror along with its rubber
insulator pads (see illustrations).

Installation

2 Installation is the reverse of removal.


Fairing - J and К models

Note: 77ie windshield is riveted to the fairing and should not be removed unless it is being renewed. Windshields are available separately from the fairing. A rivet gun is required to secure a new windshield to the fairing.




A Unscrew the nuts (arrowed)...


B... and remove the mirror


8»4 Bodywork




 


 


А Remove the screw (arrowed) and detach the duct...

Removal

1 Remove the fairing side panels (see below).

2 To improve access to the turn signal and fusebox wiring connectors (though they can be reached from the underside of the fairing), remove the screw securing the left-hand air duct to the frame (see illustration). Lift the duct to access the wiring clip underneath, then press the ends of the clip together and withdraw it from the duct (see illustration). Remove the duct. If required, also remove the right-hand duct - it doesn't have a wiring clip.

3 Disconnect the turn signal and fusebox wiring connectors (see illustration). Remove the rear view mirrors (see Section 4|.


5.2b... then release the wiring clip from its underside

4 Remove the screws securing the sides of the fairing and the bolt securing the front of the fairing to the fairing bracket (see illustrations). Carefully draw the fairing forward and off the bike (see illustration).

5 Installation is the reverse of removal. Make sure the wiring connectors are correctly and securely connected. If not removed, make sure the fairing locates correctly onto the air ducts.


Дата добавления: 2015-10-29; просмотров: 139 | Нарушение авторских прав


Читайте в этой же книге: Front brake master cylinder components | Push the caliper against the pad to create the extra room | Tighten the mounting bolt to the specified torque | B ... and tighten it to the specified torque | Remove the split pin (A) and withdraw the clevis pin (B) | Remove the spacers from the wheel | Tighten all the clamp bolts to the specified torque | Front wheel bearings | Fitting new tyres | General information |
<== предыдущая страница | следующая страница ==>
А Lift the flap and unscrew the bolt...| B ... and remove the battery

mybiblioteka.su - 2015-2024 год. (0.007 сек.)