Студопедия
Случайная страница | ТОМ-1 | ТОМ-2 | ТОМ-3
АвтомобилиАстрономияБиологияГеографияДом и садДругие языкиДругоеИнформатика
ИсторияКультураЛитератураЛогикаМатематикаМедицинаМеталлургияМеханика
ОбразованиеОхрана трудаПедагогикаПолитикаПравоПсихологияРелигияРиторика
СоциологияСпортСтроительствоТехнологияТуризмФизикаФилософияФинансы
ХимияЧерчениеЭкологияЭкономикаЭлектроника

Depending on the position of the log in the grinder magazine, it can be distinguished

Читайте также:
  1. Blue gum, chemical composition of wood 23
  2. Chemical composition
  3. Composition
  4. Composition in sulfate and sulfite
  5. Composition of Lignin, Residual Lignin after Cooking and after Bleaching
  6. Each minimal pair exemplifies a possible consonant opposition

between:

_ Transversal groundwood: Wood logs (and evidently also the

Fibers) are loaded in the magazine or pocket of the grinder transversally

(perpendicularly) to the rotational direction of the stone

(in practice the only used orientation).

_ Longitudinal groundwood: Wood logs are loaded parallel to the

Rotational direction of the stone (only applied in research studies).

Handbook of Pulp. Edited by Herbert Sixta

Copyright © 2006 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

ISBN: 3-527-30999-3

©2006 WILEY-VCHVerlag GmbH&Co.

Handbook of Pulp

Edited by Herbert Sixta

Grinding procedures may be categorized as atmospheric grinding, pressure grinding,

And thermo grinding. The principles of each process are illustrated schematically

In Fig. 4.2.

Fig. 4.2 Principles of the grinding procedures.

4.1.2

Mechanical and Thermal Processes in Grinding

Grinding is a thermomechanical process that is divided into two parts, each of

which overlaps one another: (a) Softening and breakdown of the fiber structure;

And (b) peeling of the softened fibers from the wood matrix in the grinding zone

Softening of the Fibers

The wood logs are pressed against a rotating pulp stone, applying suitable pressure

And temperature conditions (see Fig. 4.2). Just before entering the grinding

Zone, the wood logs are still cold and thermally untreated. The stone grits pass

over the wood matrix at very high frequencies. In a so-called compression/decompression

Process, the fibers are cyclically stressed or relaxed. Depending on the

Rotational speed of the pulp stone, and also on the surface profile of the stone,

Pressure pulsations up to 40 kHz occur on the logs.

The fiber matrix is loosened due to the fatigue work done by the grits. Finally,

When they enter the boundary area between the revolving stone surfaces, the

Mechanical Pulping Processes

Fibers are peeled from the outermost layer of the softened wood, much in the

Same way that tape is torn from a paper surface. Both processes warm up the

Wood and break down the fiber structure. Due to the viscoelastic nature of the

wood, the temperature at 1–2 mm above the actual grinding zone increases very

Quickly, and this rise in temperature causes the lignin to soften. The resulting

so-called “softening temperature” depends on the water content of lignin and the

frequency. In 1963, Goring [3] demonstrated how the softening temperature of

Lignin is dependent upon the water content (Fig. 4.3).

Fig. 4.3 Softening temperature of lignin depending on water

content (according to Goring [3]).


Дата добавления: 2015-10-21; просмотров: 134 | Нарушение авторских прав


Читайте в этой же книге: Parameters Viscose products Cellulose acetate High-viscosity ether | Study of different approaches for analyzing | The prehydrolysis-alkaline sulfite process | In the viscose process. Svensk. Papperstidn., | Kunze, J., A. Ebert, H.-Fink, Characterization | Composition in sulfate and sulfite | In Teltow-Seehof. Das Papier, | Fig. 1.2 An overview of the basic mechanical pulping procedures. | Straight, less knotty and free from rot. | High moisture content of the wood. For this, the wood is stored in bundles in |
<== предыдущая страница | следующая страница ==>
Wood. Wood that has been stored under dry conditions for a longer time has a| The softening temperature is understood to represent the transition of an amorphous

mybiblioteka.su - 2015-2024 год. (0.005 сек.)