Студопедия
Случайная страница | ТОМ-1 | ТОМ-2 | ТОМ-3
АвтомобилиАстрономияБиологияГеографияДом и садДругие языкиДругоеИнформатика
ИсторияКультураЛитератураЛогикаМатематикаМедицинаМеталлургияМеханика
ОбразованиеОхрана трудаПедагогикаПолитикаПравоПсихологияРелигияРиторика
СоциологияСпортСтроительствоТехнологияТуризмФизикаФилософияФинансы
ХимияЧерчениеЭкологияЭкономикаЭлектроника

Designed calculation of helical gear

Читайте также:
  1. A Simple Calculation
  2. Calculation and intuition.
  3. Calculations in Calc. Creating and Coping Formulas
  4. Calculations of exhausts of harmful substances by motor transport
  5. Design-basis calculation of the shafts
  6. Question 2: SHORT QUESTIONS / CALCULATIONS

 

Purpose of calculation: assessment of interaxial spacing and other parameters of gear, excluding chipping of teeth surface of operating gear.

Estimate value of interaxial spacing

, мм

where – torque at the wheel, Н m;

– ratio for uneven load spread along contact line – ratio of relative wheel width for any wheels under symmetrical position in relation to supports.

Calculated value (мм) should be rounded to nearest big figure according to GOST 2185-66.

1st row                        
2nd row                    

Note: values of the 1st row are preferable.

Further calculation is recommended to be done in the following sequence:

Gearing module is to be set as , mm,
with rounding up to nearest standard value.

 

 

Standard row (selection) of modules

1st row   1,25 1,5   2,5        
2nd row     1,75 2,25 2,75 3,5 4,5 5,5  

In order to set linear dimensions – diameters, lengths, heights etc the standards define rows as specified in Table 6.

Table 6.

Normal linear dimensions (GOST 6636-69)

Ra 20 Ra 40 Ra 20 Ra 40 Ra 20 Ra 40 Ra 20 Ra 40
1,0 1,00 5,6 5,6        
  1,05   6,0        
1,1 1,10 6,3 6,3        
  1,15   6,7        
1,2 1,20 7,1 7,1        
  1,30   7,5        
1,4 1,40 8,0 8,0        
  1,50   8,5        
1,6 1,60 9,0 9,0        
  1,70   9,5        
1,8 1,80 10,0 10,0        
  1,90   10,5        
2,0 2,00 11,0 11,0        
  2,10   11,5        
2,2 2,20 12,0 12,0        
  2,40   13,0        
2,5 2,50 14,0 14,0        
  2,60   15,0        
2,8 2,80 16,0 16,0        
  3,00   17,0        
3,2 3,20 18,0 18,0        
  3,40   19,0        
3,6 3,60 20,0 20,0        
  3,80   21,0        
4,0 4,00 22,0 22,0        
  4,20   24,0        
4,5 4,50 25,0 25,0        
  4,80   26,0        
5,0 5,00 28,0 28,0        
  5,30   30,0        

Note. From rows (Ra5, Ra10, Ra20, Ra40) as set by the standards the rows Ra20, Ra40 are also indicated with smaller gradation

 

All catching parameters are expressed via the following module

Width of the wheel is defined by the following equation:

, мм.

Width of the pinion is set as , мм.

Calculated dimensions should be verified with standard ones as per GOST 6636-69 (Table 6).

Helix angle to be set as follows: .

Minimum helix angle is to be .

Then the following parameters shall be defined:

- total number of gear teeth , taking as whole part of integer ;

- number of pinion teeth , rounding up to whole integer ;

- number of wheel teeth .

Helix angle value is to be refined .

Actual gear ratio shall be refined and its deviation from the set value:

, .

Then calculation of geometrical parameters of toothed wheels is to be done according to formulas as specified in Table 7

 

Table 7

Calculation of geometrical parameters of toothed wheels

Parameter Symbol Formula
     
1. Reference diameter, mm pinion
wheel

Extension of Table.


Дата добавления: 2015-10-31; просмотров: 60 | Нарушение авторских прав


Читайте в этой же книге: Design-basis calculation of the shafts | Selection of rolling bearings | Test calculation of output shaft fatigue strength | GUIDELINES TO EXECUTION OF GRAPHIC PORTION OF THE COURSE WORK |
<== предыдущая страница | следующая страница ==>
Selection of task for the course work| Reduction unit wheels layout method

mybiblioteka.su - 2015-2024 год. (0.008 сек.)