Студопедия
Случайная страница | ТОМ-1 | ТОМ-2 | ТОМ-3
АвтомобилиАстрономияБиологияГеографияДом и садДругие языкиДругоеИнформатика
ИсторияКультураЛитератураЛогикаМатематикаМедицинаМеталлургияМеханика
ОбразованиеОхрана трудаПедагогикаПолитикаПравоПсихологияРелигияРиторика
СоциологияСпортСтроительствоТехнологияТуризмФизикаФилософияФинансы
ХимияЧерчениеЭкологияЭкономикаЭлектроника

A Slide the fork up through the bottom yoke.

Читайте также:
  1. A breeze blows through the window and the top pages flutter. We both slam our palms down to catch them.
  2. A Slide on the thrust washer ... 29.15b ... the 5th gear pinion bush .
  3. At last the breeze came; the schooner sidled and drew nearer in the dark; I felt the hawser slacken once more, and with a good, tough effort, cut the last fibres through.
  4. Bottom five jobs
  5. Bottom of Form
  6. Break On Through

B... and fit the circlip and handlebar onto it


A Tighten the bottom yoke clamp bolt...


6»8 Frame, suspension and final drive



6.6b... then the fork top bolt...

torque setting (see illustration). Now tighten the fork clamp bolts in the top yoke and the handlebar holder clamp bolts to the specified torque setting (see illustration). 7 If displaced, make sure the front brake


6.6c... and finally the top yoke and

Handlebar clamp bolts to their specified

Torque settings

master cylinder clamp is installed with the UP mark facing up and tighten the clamp bolts to the torque setting specified at the beginning of the Chapter (see illustration 5.1b). 8 Install the front wheel (see Chapter 7), and


the front mudguard (see Chapter 8). Mount the front brake hose/pipe union on the fork and tighten its bolt (see illustration 6.2). 9 Check the operation of the front forks and brakes before taking the machine out on the road.

7 Forks - disassembly, ^

inspection and reassembly 5|

J, K, L and N models

Disassembly

1 Always dismantle the fork legs separately to avoid interchanging parts and thus causing an accelerated rate of wear. Store all components in separate, clearly marked containers (see illustration).

2 Before dismantling the fork, it is advised that the damper rod bolt be slackened at this stage. Compress the fork tube in the slider so that the spring exerts maximum pressure on the damper rod head, then have an assistant slacken the damper rod bolt in the base of the fork slider (see illustration 7.31), If an assistant is not available, clamp the slider via its brake caliper mounting lugs in a soft-jawed vice to support the fork. If required, remove the circlip securing the mudguard holder to the top of the fork slider and remove the holder.

3 If the fork top bolt was not slackened with the fork in situ, release any air pressure in the forks on J and К models and adjust the spring pre-load to a minimum on L and N models (see Section 12), then carefully clamp the fork tube in a vice equipped with soft jaws, taking care not to overtighten or score its surface, and slacken the top bolt.

4 Unscrew the fork top bolt from the top of' the fork tube (see illustration).

A Warning: The fork spring is pressing on the fork top bolt with considerable pressure. Unscrew the bolt very carefully, keeping a downward pressure on it and release it slowly as it is likely to spring clear. It is advisable to wear some form of eye and face protection when carrying out this operation.

I


 


       
   


1 Top bolt (L and N model 7 Damper rod
shown) 8 Rebound spring
2 O-ring 9 Fork tube
3 Spacer 10 Bottom bush
4 Spring seat 11 Dust seal
5 Spring 12 Retaining clip
13 Oil seal

6 Piston ring


 

14 15 16 17 18 19

Washer Top bush Damper rod seat Fork slider Sealing washer Damper rod bolt

20 Me clamp bolt


Дата добавления: 2015-10-29; просмотров: 179 | Нарушение авторских прав


Читайте в этой же книге: A Slacken the bracket screw (arrowed) and release the outer cable ... | L, N and R models | Fairly difficult, | Primary circuit connectors from the coils | A Pulse generator coil wiring connector (arrowed) - J and К models | B ... then install the cover | General information | Very drfficurt, | Slacken the lockouts (A), then unscrew the linkage rod (B) | Note how the lug (A) locates in the hole (B) |
<== предыдущая страница | следующая страница ==>
C If required, slacken the fork top bolt 6.4a Slacken the clamp bolt (arrowed) in| Prise off the bottom bush using a flat-bladed screwdriver

mybiblioteka.su - 2015-2024 год. (0.009 сек.)