Студопедия
Случайная страница | ТОМ-1 | ТОМ-2 | ТОМ-3
АвтомобилиАстрономияБиологияГеографияДом и садДругие языкиДругоеИнформатика
ИсторияКультураЛитератураЛогикаМатематикаМедицинаМеталлургияМеханика
ОбразованиеОхрана трудаПедагогикаПолитикаПравоПсихологияРелигияРиторика
СоциологияСпортСтроительствоТехнологияТуризмФизикаФилософияФинансы
ХимияЧерчениеЭкологияЭкономикаЭлектроника

D. HUD Display in Setup Mode

Читайте также:
  1. BIOS FEATURES SETUP 2 страница
  2. BIOS FEATURES SETUP 3 страница
  3. BIOS FEATURES SETUP 4 страница
  4. Display Modes
  5. Displaying multiple views of a table
  6. Exercise 3. To display on a screen the value of system constantpand to set the maximal format of her displaying locally.

* The following operations are made by pushing the dial button forward, backward or down (vertically) to adjust the values of the selections.

l Set engine displacement: The default value is 1.8L, and you can change that by using the dial button.

 

 

 

 

l Unit setup: The default units are ЎгC and Km/H. Push the dial button forward to change it between ЎгC and ЎгF. Push downward to change between MPH and Km/H.

l Over speed warning: The default value is 120KM/H. The over speed warning icon will light if the speed is higher than the preset value and will stop flashing when the speed is lower than the preset value.

l Time setup: By default, the hour icon is flashing. Use the dial button to adjust the value and press OK (downward) to confirm the setup and then enter into minute setup.

 

l Water Temp Warning Setup: The default value is 105ЎгC. If the temp is higher than the preset value, it will flash. It will stop flashing if the temp is lower than that value.

l Battery Voltage setup: The default value is 10.5V. The warning icon will light if the voltage is lower than preset and will disappear when the voltage is higher than that.

l Tired Driving Notice: The default value is 4.0 Hours. It will give a warning if the continuous drive time is longer than that.

l Gear Shift Notice: The default value is 5000 RPM. It will light if the rotation speed is higher than the preset value.

 

l The speed to give gear shifting notice: The default value is 70 KM/H. if the speed is higher than that, there will no notice.

l Fuel Consumption Calibration: It is 100% by default. The current value is the actual consumption (read from OBD) multiplied by the preset percentage. It can be adjusted.

l Speed Calibration: It is 100% by default. The current speed is the actual value (read from OBD) multiplied by the preset percentage.

l Whether to diagnose engine error: It is ON by default. When ON it flashes to give a warning.

 

 

l Engine Error Scanning: At this step the system will scan the engine. It will show NO if there is no error. If there is an error it will show the error code. Pressing the button for 3 seconds clears the error code.

 


Дата добавления: 2015-10-29; просмотров: 137 | Нарушение авторских прав


Читайте в этой же книге: Easy Baza MANUAL | B. Where to put the HUD in the car | C. How to use the polarizing film |
<== предыдущая страница | следующая страница ==>
Function Introduction| Pre-Text Assignments

mybiblioteka.su - 2015-2024 год. (0.005 сек.)